MCP23017 5V LCD 1602/2004/12864 Expander I2C IIC Serial Interface Module

Description

Home
Electronic Component
Chips
Sensor
Arduino Module
Raspberry Pi
MCP23017 5V LCD 1602/2004/12864 Expander I2C IIC/SPI Serial Interface Module
Popular
Popular
Product Introduction
Description:
MCP23017 I2C/SPI Interface
• 16-Bit Remote Bidirectional I/O Port:
- I/O pins default to input
• High-Speed I2C Interface (MCP23017):
- 100kHz
- 400kHz
- 1.7MHz
• High-Speed SPI Interface (MCP23S17):
- 10 MHz (maximum)
• Three Hardware Address Pins to Allow Up to
Eight Devices On the Bus
• Configurable Interrupt Output Pins:
- Configurable as active-high, active-low or
open-drain
• INTA and INTB Can Be Configured to Operate
Independently or Together
• Configurable Interrupt Source:
- Interrupt-on-change from configured register
defaults or pin changes
• Polarity Inversion Register to Configure the
Polarity of the Input Port Data
• External Reset Input
• Low Standby Current: 1 μA (max.)
• Operating Voltage:
- 1.8V to 5.5V @ -40°C to +85°C
- 2.7V to 5.5V @ -40°C to +85°C
- 4.5V to 5.5V @ -40°C to +125°C
Package Included:
1PC*Bidirectional 16-Bit I/O Expander with I2C IIC Serial Interface Module MCP23017
1602/2004/12864 LCD
This is a brand-new design.
Uses MCP23017 chip, it is compatible with 1602 and 12864 liquid crystal screens, through this module is switched, use I2C communication, only need two MCU I/Os to be able to realize the liquid crystal to drive the display.
The potentiometer on the module can achieve contrast adjustment. You can also unplug the jump cap to turn off the backlight or adjust the brightness through PWM. We provide wiring diagram and arduino sample code, isn't it great!
Supply voltage: 5V
the backlight and contrast is adjusted by potentiometer
Compatible for 1602 LCD 2004 LCD 12864LCD
Package Included:
1PC*Arduino 5V 1602/2004/12864 IIC/I2C LCD Serial Interface MCP23017 Expander Module
MCP23017-E/SO IC
MCP23017 SOP-28 MCP23017-E/SO 16-Bit I/O Expander I2C Interface IC
Package Included:
1PC*MCP23017 SOP-28 MCP23017-E/SO 16-Bit I/O Expander I2
MCP23017-E/SP IC
MCP23017-E/SP DIP-28 MCP23017 16-Bit I/O Expander with I2C Interface IC
Package Included:
1PC*MCP23017-E/SP DIP-28 MCP23017 16-Bit I/O Expander with I2C Interface IC
I2C Interface Board
This is another great IIC/I2C/TWI/SPI Serial Interface. As the pin resources of Arduino controller is limited, your project may be not able to use normal LCD shield after connected with a certain quantity of sensors or SD card. However, with this I2C interface module, you will be able to realize data display via only 2 wires. If you already has I2C devices in your project, this LCD module actually cost no more resources at all. It is fantastic for Arduino based project.
I2C Address: 0X20~0X27 (the original address is 0X20,you can change it yourself)
Supply voltage: 5V
the backlight and contrast is adjusted by potentiometer
Come with 2 IIC interface, which can be connected by Dupont Line or IIC dedicated cable
Compatible for 1602 LCD 2004 LCD
Package Included:
1PC*IIC I2C Adapter Serial Interface Board Module 5v Arduino 1602 2004 LCD
Payment
Shipping
Refund
Payment
We accept PayPal only.
But we only
Accept
your
Ebay Address
,Please Make sure it's 100% right.
Payment must be received in 5 business days of auction closing.
Please leave note for your special request (e.g. Colors or Size) in PayPal when you pay the order.
Any special request cannot be accepted after 24 hours of payment, because most of orders will be processed instantly and same day dispatched.
Shipping
We maintain high standards of excellence and strive for 100% customer satisfaction! Feedback is very important to us. We request that you contact us immediately BEFORE you give us neutral or negative feedback, so that we can satisfactorily address your concerns.
Refund
All package need to
wait 30 days
(US only n
eed 7-10 days)
,
Please take care it.Less than 30 days,we can't take a refund
.
If the item is defect when you receive it or you are not satisfied with it, please return it within 14 days for a replacement or money back. But the items must be back in factory condition. Please contact us and double check the return address before you return it.
If is item is defective in 12 months, you can return it to us. We will send you a new replacement after receiving the defective item.